ASTM A635 PDF

This standard is issued under the fixed designation A /A M; the 1 This specification is under the jurisdiction of ASTM Committee A ASTM A/AM: Standard Specification for Steel, Sheet and Strip, Heavy- Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural. Find the most up-to-date version of ASTM A at Engineering

Author: Guzil Gardagore
Country: Bulgaria
Language: English (Spanish)
Genre: Health and Food
Published (Last): 21 December 2008
Pages: 349
PDF File Size: 20.98 Mb
ePub File Size: 5.63 Mb
ISBN: 258-7-62414-371-1
Downloads: 82380
Price: Free* [*Free Regsitration Required]
Uploader: Dubar

AK Steel ASTM A and A Hot Rolled Carbon Steel, Structural Steel (SS)

Size Limits, Coils Only. The analysis shall be from a test sample preferably taken during the pouring of the heat or cast.

Test Reports and Certi? Approved May 1, Current edition approved Sept. Such a deviation is obtained by placing an 8-ft straightedge on the concave side and measuring the greatest distance between the strip edge and the straightedge.

Rejection and Rehearing The mechanical property requirements, number of specimens, test locations, and specimen orientation shall be in accordance with the applicable product specification. This specification covers the general requirements for hot-rolled, heavy-thickness, and high-strength low-alloy with improved formability sheet and strip coils.

The term weight is used when inch-pound units are the standard. The several determinations of any element in a cast shall not vary both above and below the speci? Historical Version s – zstm previous versions of standard. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

To see MatWeb’s complete data sheet for this material including material property data, metal compositions, material suppliers, etcplease click the button below. The purchaser is advised to discuss this change with the supplier.

Data sheets for overmetals, plastics, ceramics, and composites. Combining values from the two systems may result in nonconformance with this specification.

  KBA 70219 ABE PDF

Steels may be produced as ingot-cast or strand-cast. Or if you don’t have an account with us yet, then click here to register.

Please contact us at webmaster matweb. The sampling may asm facilitated by folding the sheet both ways, so that several samples may be taken at one drilling. Such a deviation is obtained by placing a mm straightedge on the concave side and measuring the greatest distance between the strip edge and the straightedge.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phoneastmmor service astm. Therefore, users must analyze chips taken from the steel in the condition in which it is received from the steel manufacturer.

ASTM A635 Grade 1018

For strip over 8 in. Product analysis is appropriate on these types of steel only when misapplication is apparent, or for copper when copper steel is speci?

Over Over A35 Over Over Over Over Over Over Over Over Over Over Over ast 14 17 19 21 24 26 28 35 50 60 65 70 80 to to to to to to to to to to to to to 14, 17, 19, 21, 24, 26, 28, 35, 50, 60, 65, 70, 80, incl incl incl incl incl incl incl asgm incl incl incl incl incl Tolerance Over Speci?

Over 8 to 12 A The manufacturer must be consulted. Depending upon the angle of the bevelled edge cut, the width of the narrow surface of the cut-edge coil may be less than the minimum ordered width. The manufacturer shall be noti?

These tolerances do not include crown, and, therefore, the tolerances given in Table A1. Please read our License Agreement regarding materials data and our Privacy Policy. However, under SI, the preferred term is mass. For steels other than non-killed capped or rimmedproduct analysis may be made.

  KLUBERSYNTH UH1 14-31 PDF

Combining values from the two systems may result z635 nonconformance with this speci? Crown Tolerances for Satm Steel subjected to certain heating operations by the purchaser may not give chemical analysis results that properly represent its original composition.

We also ask that you refer to MatWeb’s terms of use regarding this information. This standard has been approved for use by agencies of the Department of Defense.

Conformance to Annex A1 is mandatory when the “M” specification is used.

Steels may or may not be subjected to tension test requirement. Questions or comments about MatWeb? Workmanship, Finish, and Appearance 9. Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the content of the report.

Camber should not exceed astmm in. Cut Edge and 3? Packaging and Package Marking If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Within the text, the SI units are shown in brackets. Over 8 to 12, incl Speci?

Link to Active This link will always route to the current Active version of the standard. NOTE 2—Micrometers used for measurement of thickness shall be constructed with anvils and spindles having s635 diameters asstm 0.

These tolerances do not include crown, and, therefore, a365 tolerance given in Table A1. Approved March 1, The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values.

Author: admin